Your Complete Tutorial for Bathtub Installation
Your Complete Tutorial for Bathtub Installation
Blog Article
This great article below in relation to A Step-by-Step Guide to Installing a Bathtub is fairly motivating. You should investigate it.
Mounting a bathtub isn't specifically rocket science, however it does call for strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is likewise a moderately challenging job. If the old bathtub is readily available, the job can move immediately; if you have to open up a wall surface to get rid of the old tub and also position the brand-new tub, the task is much harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to vacate the old bathtub and also set in the brand-new one. Ensure you have certified yourself for the job and fit trying it. As opposed to working with a professional to take control of a halfway-completed task, it is better to take into consideration employing one before you begin. Opportunities are you may require an expert plumber to make tube links.
This post will help you mount a brand-new bath tub in your restroom if you have already purchased a new bathtub as well as don't need to transform the plan of your previous water system pipes.
Your tools as well as material checklist must make up the following:
Getting ready for the Installation
Firstly, the supporting frame provided with the bathroom must be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets device to avoid strain on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you must do is separate the water. After doing so, activate the taps to drain any kind of water staying in the system. The process of removing the existing taps can be rather problematic as a result of the restricted access that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, put the bathtub in the required position. The wooden boards are handy in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four small points.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub up until the spirit level checks out level.
To install faucets, fit the bottom of the furthest versatile tap adapter to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
Switch on the supply of water and examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill up the bath tub and additionally check the overflow electrical outlet as well as the regular outlet for leakages.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub needs to wait until the bath tub has been made use of at the very least when as this will resolve it into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washers remain in location between the faucet and the sink. Safeguard the tap in position with the maker provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal tap adapters. The former kind should be attached to the tap finishes initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, creating the water to permeate the wall surface between the bath and the tiling, bring about problems with moisture and feasible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes and also cartridges, and also can securing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before sealing, to allow for the motion experienced when the tub remains in use. The sealer can break fairly early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently offered on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very focused on Tools You Need to Install a New Bathtub and I really hope you appreciated the piece. Sharing is caring. You won't know, you may very well be helping someone out. I value reading our article about A Step-by-Step Guide to Installing a Bathtub.
Expert plumbing diagnostics and repair. Report this page